Shot

Cavity is the hollow region inside the mold that shapes the exterior of the molded part. Together with the core, it defines the final geometry: whatever the melt fills is exactly what becomes the part after cooling. ## Cavity vs. core - Cavity (female side): usually the fixed half of the mold, defines the cosmetic / outer surface. - Core (male side): usually the moving half, defines the inside and houses the ejector pins. The line where the two halves meet is the parting line. ## Single- vs. multi-cavity molds - 1 cavity: prototypes, large parts, low-volume technical work - 2, 4, 8, 16 cavities: medium production (containers, caps) - 32, 64, 96, 128 cavities: high production (PET closures, preforms) - Family molds: different cavities in the same tool to produce a set of parts ## Critical design considerations Balanced runners so all cavities fill simultaneously, symmetrical cooling, draft angle on every vertical wall, surface finish (texture, VDI or SPI polish), and replaceable inserts in high-wear areas (gates, cores). ## Typical cavity defects Imbalance in multi-cavity molds (some parts with flash, others short), scratches from misalignment, ejector marks from poor pin placement, and localized wear at gates of cavities with weaker cooling.

Molding Cycle is the complete sequence of phases that produces one injection-molded part, from mold close to the next mold open. Each phase contributes its time and together they determine press productivity and part cost. ## Phases of the cycle 1. Clamp close and full tonnage applied 2. Injection: the screw forces molten material into the cavity along a velocity profile 3. Hold (packing): constant pressure to compensate for shrinkage during initial cooling 4. Cooling + plasticizing: the screw rotates to prepare the next shot while the part cools 5. Clamp open 6. Ejection and robot / EOAT motion ## How to calculate cycle time Cycle time is the sum of every phase: Cycle time = clamp close + injection + hold + cooling + mold open + ejection Plasticizing (screw recovery) runs in parallel with cooling, so it only counts when it is longer than the cooling phase. Cooling dominates and scales with the square of the thickest wall: doubling wall thickness roughly quadruples cooling time. This wall-thickness rule is the single biggest lever on overall cycle time. ## Cycle time example A representative thin-wall part on a 150-ton press: | Phase | Time | |-------|------| | Clamp close | 1.0 s | | Injection | 1.5 s | | Hold | 4.0 s | | Cooling | 8.0 s | | Mold open + eject | 2.0 s | | Total cycle | 16.5 s | ## How does material affect the cycle? Semi-crystalline resins (PP, PA, POM, HDPE) release more latent heat as they crystallize and usually need longer cooling than amorphous resins (ABS, PC, PS) at the same wall thickness. Melt temperature, mold temperature and the resin's ejection (heat-deflection) temperature all set the minimum cooling time. ## Optimization Conformal cooling channels that follow part geometry, a multi-stage injection profile, plasticizing in parallel with opening, valve gates on hot runners for clean closure, and elimination of dead time on the robot side. ## How long is an injection molding cycle? Thin-wall packaging parts cycle in 3–15 s, while thick technical or engineering parts can take 30–60 s or more. Cooling sets the floor: the thicker the wall, the longer the minimum achievable cycle. ## Which phase takes the longest? Cooling, almost always. It typically accounts for 50–70 % of the total cycle, which is why conformal cooling and wall-thickness reduction give the biggest gains. ## What is the difference between molding cycle and cycle time? "Molding cycle" describes the sequence of phases; "cycle time" is the numerical total in seconds reported on the cell's OEE. The cycle is the what, the cycle time is the how long.

Shot size is the volume of melt the screw meters and injects each cycle — set as a screw-position stroke (mm) or a volume (cm³). It is the volumetric twin of shot weight, which is the same material expressed as mass. ## How it is set - During recovery (dosing) the screw rotates and retracts to a set position; that retraction distance defines the shot size. - Set it so the first-stage (velocity-controlled) fill reaches about 95–99 % of the part, then hold packs it out — leaving a stable cushion so the screw never bottoms out. - The shot should use roughly 20–80 % of the barrel's rated capacity (see barrel occupancy) to keep residence time in range. ## Why it matters Shot size drives part-weight repeatability and where the transfer position cut off lands. Too small and you cannot fill the part and still keep a cushion; too large and you waste material, stretch residence time and risk degradation. ## Shot size vs shot weight - Shot size: the volume or screw stroke the machine delivers per cycle. - shot weight: the mass of that same shot (parts + runners + sprue), read on a scale. Shot size × melt density ≈ shot weight. ## Related terms - See also: shot weight, cushion, recovery, barrel occupancy, transfer position cut off ## What is shot size in injection molding? It is the metered volume (or screw stroke) of melt injected per cycle, set during recovery so the part fills on first stage and a cushion remains. ## How do you set shot size? Dose to a screw position that fills about 95–99 % on first stage and leaves a small, stable cushion, keeping the shot within roughly 20–80 % of barrel capacity. ## What is the difference between shot size and shot weight? Shot size is volumetric (screw stroke or cm³); shot weight is the mass of the same shot in grams. Multiplying shot size by melt density gives approximately the shot weight.

Shot weight is the total mass of plastic injected in one cycle — every cavity's molded part plus the runners and sprue. It is the number you read by weighing one full shot on a scale, and it drives machine sizing, dosing and several derived calculations. ## How to find it - Weigh one complete shot (parts + runners + sprue) on a gram scale — that is the shot weight. - Or estimate it: shot weight = (part weight × number of cavities) + runner and sprue weight. - By volume: shot weight = shot volume × melt density of the resin. ## Why it matters - Machine selection: the shot should sit comfortably inside the barrel's usable range — neither so small that residence time stretches out, nor so close to the maximum that melt quality suffers (see barrel occupancy). - Material planning: shot weight × cycles = resin consumption, including the scrap from runners. - Process setup: it anchors the dosing stroke and the transfer-to-cushion position. ## Shot weight vs related terms - Part weight / cavity weight: only the molded part(s), without runners. - shot size: usually the volumetric stroke (cm³ or mm of screw travel) that delivers the shot weight. ## Related terms - See also: shot size, barrel occupancy, residence time, cavity weight, cushion ## What is shot weight in injection molding? It is the total grams of plastic injected per cycle — all parts plus runners and sprue — found by weighing one full shot. ## How do you calculate shot weight? Multiply part weight by the number of cavities and add the runner and sprue weight, or weigh a complete shot directly on a scale. ## What is the difference between shot weight and part weight? Part weight is only the molded part; shot weight adds the runners and sprue, so it is always equal to or greater than the combined part weight.

Transfer position (Cut-Off / V/P switchover) is the screw position at which the controller switches from velocity control (injection phase) to pressure control (hold phase). It is one of the most critical settings in scientific molding: it ends dynamic fill and begins packing. ## Why it matters During injection, velocity (cm³/s or mm/s) is controlled; during hold, pressure (bar) is controlled. Transferring too late over-packs the cavity (flash, internal stress); too early causes short shot or sink marks. ## How to set it - Fill 95 – 99 % of the cavity on velocity, leaving the rest to hold - Final cushion: should be 5 – 10 % of shot size, stable and repeatable - "Pressure vs. time" method: transfer before injection pressure saturates ## Transfer methods - By screw position (most common and reproducible) - By time since start of injection (least precise) - By hydraulic / plastic pressure (V/P switch by pressure) - By cavity pressure sensor (most accurate, advanced scientific molding) ## Indicators of a well-tuned transfer - Cushion stable shot-to-shot (±0.5 mm) - Repeatable fill time - Reproducible injection pressure peaks - No flash on any cavity in a multi-cavity tool ## Common issues Late transfer with flash, early transfer with short shot, cushion drift from check-valve wear, and multi-cavity imbalance requiring per-cavity tuning with pressure sensors.