Continuous Recirculation

The carbon footprint of an injection-molded part is the total greenhouse gas emitted to make it, expressed as kilograms of CO₂-equivalent (kg CO₂e) per part or per kilogram of plastic. For a molder it is a life-cycle figure with a few dominant contributors — and most of them are levers the shop can pull. ## Where the emissions come from - The resin itself: producing virgin resin from fossil feedstock is usually the single largest share — often several kg CO₂e per kg of plastic, before a part is even molded. - Process energy: the electricity the press, dryers and chillers consume each overall cycle time. Long cycle time, oversized machines and hydraulic presses raise it. - Scrap & regrind: every rejected molded part, runner and purge that becomes scrap carries its embodied carbon; reusing it as regrind recovers that energy. - Transport & end of life: shipping resin and parts, and whether the part is landfilled, incinerated or recycled. ## How molders reduce it - Cut process energy: all-electric machines, shorter overall cycle time, right-sized presses, efficient drying and insulated barrels. - Use less and reuse: lighter parts, less runner/sprue waste, higher regrind ratios and recycled or bio-based resin instead of pure virgin resin. - Lean operations: lean manufacturing reduces scrap, rework and idle running, all of which carry carbon. - Chemical recycling: routes like depolymerization can return plastic to feedstock instead of landfill. ## Why it matters Customers increasingly require a part's carbon footprint for their own reporting, and it is becoming a purchasing criterion alongside price and quality. Measuring it (often as a cradle-to-gate LCA) lets a molder target the biggest levers — usually resin choice and process energy. ## Related terms - See also: resin, virgin resin, regrind, overall cycle time, depolymerization ## What is the carbon footprint of a plastic part? The total greenhouse gas emitted to produce it, in kg CO₂e — dominated by the resin's production, the process energy of the molding cell, and scrap, plus transport and end of life. ## How can an injection molder reduce carbon footprint? Lower process energy (all-electric machines, shorter cycles, efficient drying), reduce material and scrap, raise regrind and recycled-content ratios, choose lower-carbon or bio-based resins, and apply lean practices to cut waste. ## What contributes most to a molded part's carbon footprint? Usually the production of the virgin resin, followed by the electricity used per cycle by the press and auxiliaries; scrap, transport and end-of-life add the rest.

Regrind is plastic material recovered by grinding runners, sprues, defective parts or purges, then blended with virgin resin and reintroduced into the process. It is a key sustainability and cost-reduction tool in injection molding. ## Why use regrind Recovers the ~20 – 30 % unavoidable scrap from cold runners and cuts raw-material cost by 5 – 25 %, with a lower carbon footprint. On non-critical parts, pure or near-pure regrind is fully viable. ## Typical proportions (regrind/virgin blend) - Cosmetic / engineering parts: 10 – 20 % - Non-visible structural parts: 20 – 50 % - Internal / non-critical: 50 – 100 % - Some resins (PVC, PE): up to 100 % in approved applications ## Regrind system equipment - Granulator: rotating blades, sizing screen - Pellet size: 3 – 8 mm for homogeneous mix with virgin - Beside-the-press: granulator next to the machine, regrind returns to the hopper via blower - Magnet + metal detector: mandatory to avoid screw damage - Volumetric or gravimetric blender: meters regrind and virgin in a defined ratio ## Limitations and issues - Cumulative thermal degradation each pass (lowers viscosity, properties) - Cross-contamination with another resin causes delamination or breakage - Yellowing or graying on unpigmented resins - Property loss in multi-generation regrind - FDA / medical / automotive restrictions forbid uncertified regrind ## Disallowed applications FDA food-contact, class II/III medical devices, structural crash parts in automotive, and certain children's toys under specific regulation.

The regrind process is the procedure a molder follows to turn in-house plastic scrap — runners, sprues, rejected parts and purge — into reusable regrind flakes that can be blended back with virgin resin. It is the workflow; the material it produces is regrind, the equipment that does it is the regrind system, and how many times material has been through it is the regrind generation. ## Typical steps 1. Collect & sort: keep scrap clean, dry and separated by resin and color — contamination cannot be undone later. 2. Granulate: a granulator cuts the scrap into flakes sized close to a pellet so they feed and melt like virgin. 3. De-dust / screen: remove fines and oversize; dust and long slivers cause feeding and quality problems. 4. Blend: meter the regrind into virgin resin at a controlled ratio (often 10–30 %), usually with a dosing unit. 5. Dry & re-mold: regrind re-absorbs moisture quickly, so it is dried with the virgin before going back to the machine. ## Why control it Each pass through the process adds a heat history that shortens polymer chains, so an uncontrolled regrind process degrades parts and destabilizes the cycle. A documented procedure — clean handling, fixed blend ratio, drying, limited generations — is part of a real quality system and is what lets regrind cut cost and waste without hurting the molded part. ## Related terms - See also: regrind, regrind system, regrind generation, virgin resin, scrap ## What is the regrind process in injection molding? The workflow of collecting in-house scrap (runners, sprues, rejects), granulating it into flakes, de-dusting, blending it with virgin resin at a controlled ratio, drying and re-molding — so usable material is recovered instead of discarded. ## What are the steps to reprocess plastic regrind? Collect and sort clean scrap by resin and color, granulate it into pellet-sized flakes, screen out dust and oversize, blend it into virgin at a set percentage, then dry and re-mold it with the virgin resin. ## Why must the regrind process be controlled? Because every reprocessing cycle adds heat history that degrades the polymer; controlling cleanliness, blend ratio, drying and the number of generations keeps part quality and process stability acceptable.

Scrap is any material or product that leaves the molding process without becoming a saleable part: defective mouldings plus non-part plastic such as runners, sprues, start-up shots and purgings. It is tracked as a scrap rate and is one of the largest hidden costs in an injection molding plant. ## Two kinds of scrap - Process scrap: runners, sprues, flash, start-up and changeover shots — usually clean and recyclable as regrind. - Reject scrap: parts that failed inspection — short shot, flash, sink marks, burns, splay, contamination or dimensional fails. ## Scrap rate Scrap rate = scrap ÷ total produced (by count or by mass). Example: 60 rejects in 2,000 shots = 3 %. It feeds the quality term of OEE; a 3 % scrap rate means 3 % of your machine time, resin and labor produced nothing to sell. ## Why it matters and how to reduce it Resin is usually the biggest cost in a molded part, so every scrapped gram is lost money plus the energy spent making it. Reduce it with a stable, documented process window (scientific molding), mold and dryer maintenance, and root-cause work on the dominant defect. Some process scrap returns as regrind, but regrind ratios are capped because reprocessing degrades the polymer. ## Related terms - See also: regrind, short shot, flash, runner, sprue ## What is scrap in injection molding? It is everything that does not ship: rejected parts plus runners, sprues, start-up shots and purge. It is measured as a scrap rate against total production. ## What is the difference between scrap and regrind? Scrap is the discarded material; regrind is scrap that has been ground up to be re-melted and reused. Clean process scrap becomes regrind, while contaminated or degraded scrap is waste. ## How do you reduce the scrap rate? Stabilize the process to a documented window, keep molds and dryers maintained, attack the top defect by root cause, and use a hot-runner or smaller-runner design to cut process scrap.