Injection Stages

Fill (First Stage) is the phase of the cycle in which the screw advances under velocity control, filling the mold cavity approximately to 95 – 99 % of its volume. It ends at the transfer point, where control switches to pressure. ## Key characteristics - Control: velocity (mm/s or cm³/s), not pressure - Purpose: fast and reproducible dynamic filling - Duration: 0.3 – 5 s typically - Volume filled: 95 – 99 % of cavity ## Why separated from hold First stage prioritizes velocity for a uniform flow front; second stage (hold) prioritizes constant pressure to compensate shrinkage. Mixing both in a single-stage process reduces quality and increases variability. ## Multi-stage profile Modern machines allow 5 – 10 velocity steps along the screw stroke: 1. Slow at gate entry (avoids jetting) 2. Fast in wide cavities 3. Slow near critical vents 4. Slow at end for smooth transition ## Typical parameters - Velocity: 30 – 200 mm/s depending on part and resin - Actual pressure (not control): may hit saturation if geometry is restrictive - Time: 0.5 – 3 s on technical parts - Residual volume: 5 – 10 % cushion as margin for hold stage ## Indicators of a good first stage - Uniform flow front (visible in short-shot studies) - Repeatable fill time (±2 % shot-to-shot) - Repeatable pressure peak - Stable final cushion ## Common mistakes - Velocity too high: jetting, splay, burn marks - Velocity too low: cold parts, visible weld lines, short shot - Late transfer: flash, over-pack - Early transfer: sinks, low dimensions

The fill second stage is the second of the injection stages: the pressure-controlled pack and hold phase that follows the velocity-controlled first stage. The screw hands off at the transfer position cut off when the cavity is roughly 95–99 % full, and the machine switches from filling by speed to pressing on the melt by pressure — applying hold pressure to finish filling and compensate for shrink. ## What happens in second stage - Pack: a brief, higher pressure tops off the last 1–5 % of the cavity and densifies the part so it copies the steel. - Hold: pressure is maintained while the gate is still open, pushing extra melt in to make up for the volume the plastic loses as it cools and contracts (contraction). Hold ends when the gate freezes — more hold after that does nothing. - Cushion preserved: a small cushion must remain so the screw can keep transmitting pressure during hold. ## First vs second stage - First stage (fill): velocity-controlled, fills ~95–99 %, sets the flow-front behavior and most cosmetic results. - Second stage (pack/hold): pressure-controlled, finishes the fill and sets part weight, dimensions and sink/voids. Separating the two cleanly at the transfer position cut off is the heart of decoupled, scientific molding. ## Why it matters Second stage governs the things customers measure: dimensions, weight and internal soundness. Too little pack/hold gives short shots, sink and voids; too much gives flash, overpacking, high stress and ejection problems. Hold time is set by a gate-seal study (weigh the part as hold time increases until weight stops rising). ## Related terms - See also: injection stages, hold pressure, transfer position cut off, cushion, contraction ## What is the fill second stage in injection molding? The pressure-controlled pack-and-hold phase after the velocity-controlled first stage; it tops off the last few percent of the cavity and holds pressure to compensate for shrink, setting part weight and dimensions. ## What is the difference between first and second stage? First stage (fill) is velocity-controlled and fills ~95–99 % of the cavity; second stage (pack/hold) is pressure-controlled, finishes the fill and compensates for cooling shrink — they switch at the transfer/cut-off position. ## How do you set second-stage hold time? With a gate-seal (gate-freeze) study: increase hold time and weigh the part each step; once part weight stops increasing, the gate has frozen and that is the minimum effective hold time.

Hold Stage (Packing Phase) is the second fill phase of the mold, after the transfer point, in which the screw applies a controlled pressure (not velocity) to compensate for shrinkage while the material cools. It ends when the gate freezes and material can no longer flow. ## Difference vs. injection phase - Injection (fill): velocity control, dynamic filling to ~95 – 99 % of cavity - Hold (packing): pressure control, packs the last 1 – 5 % and compensates shrinkage ## Typical parameters - Pressure: 40 – 80 % of peak injection pressure - Time: until gate seal (typically 2 – 10 s) - Multi-stage: 2 – 4 steps decreasing as the gate freezes - Final cushion: 5 – 10 % of shot size, stable ## When to raise/lower - Raise if: sinks, voids, low dimensions, weight below target - Lower if: flash, over-pack, internal stress, ejection difficulty ## How to verify good hold — gate seal study Weigh parts at increasing hold times; weight should plateau once the gate freezes. Optimal time = first point at which weight no longer grows. ## Common issues Zero cushion (missing material), large cushion (hold too short or gate sealed early), saturated pressure (upstream restriction), and cavity imbalance in multi-cavity molds.

Molding Cycle is the complete sequence of phases that produces one injection-molded part, from mold close to the next mold open. Each phase contributes its time and together they determine press productivity and part cost. ## Phases of the cycle 1. Clamp close and full tonnage applied 2. Injection: the screw forces molten material into the cavity along a velocity profile 3. Hold (packing): constant pressure to compensate for shrinkage during initial cooling 4. Cooling + plasticizing: the screw rotates to prepare the next shot while the part cools 5. Clamp open 6. Ejection and robot / EOAT motion ## How to calculate cycle time Cycle time is the sum of every phase: Cycle time = clamp close + injection + hold + cooling + mold open + ejection Plasticizing (screw recovery) runs in parallel with cooling, so it only counts when it is longer than the cooling phase. Cooling dominates and scales with the square of the thickest wall: doubling wall thickness roughly quadruples cooling time. This wall-thickness rule is the single biggest lever on overall cycle time. ## Cycle time example A representative thin-wall part on a 150-ton press: | Phase | Time | |-------|------| | Clamp close | 1.0 s | | Injection | 1.5 s | | Hold | 4.0 s | | Cooling | 8.0 s | | Mold open + eject | 2.0 s | | Total cycle | 16.5 s | ## How does material affect the cycle? Semi-crystalline resins (PP, PA, POM, HDPE) release more latent heat as they crystallize and usually need longer cooling than amorphous resins (ABS, PC, PS) at the same wall thickness. Melt temperature, mold temperature and the resin's ejection (heat-deflection) temperature all set the minimum cooling time. ## Optimization Conformal cooling channels that follow part geometry, a multi-stage injection profile, plasticizing in parallel with opening, valve gates on hot runners for clean closure, and elimination of dead time on the robot side. ## How long is an injection molding cycle? Thin-wall packaging parts cycle in 3–15 s, while thick technical or engineering parts can take 30–60 s or more. Cooling sets the floor: the thicker the wall, the longer the minimum achievable cycle. ## Which phase takes the longest? Cooling, almost always. It typically accounts for 50–70 % of the total cycle, which is why conformal cooling and wall-thickness reduction give the biggest gains. ## What is the difference between molding cycle and cycle time? "Molding cycle" describes the sequence of phases; "cycle time" is the numerical total in seconds reported on the cell's OEE. The cycle is the what, the cycle time is the how long.